Flooring Nail Guns review:Guns available on the market place
Includes 3-in-1 15.5/16-Gauge 2 in. Flooring Nailer/Stapler - SFL618
This pneumatic hardwood-floor stapler is a compact, mallet-actuated air stapler that automatically positions and drives staples for rapid installation of hardwood flooring. It secures the flooring at the proper angle and penetration without the danger of hammer marring. By simply resting the nose of the machine squarely against the work, the direction and angle of the staple is automatically aligned. This stapler is easily adjusted to handle different flooring thickness or tongue positions. This tool has an aluminum body for job site durability and low weight, and comes with an extra-wide composite base plate for added stability. It provides 420 in./lbs. of driving power, and has an operating pressure of 60 and 100 psi. It shoots fasteners between 1-1/2 to 2 inches, and the magazine has 92 fastener capacity.
Freeman PFL618BR Features: -3-in-1 Flooring gun with hard case. -Anodized aluminum magazine. -Air filter / anti dust cap. -One piece driver blade. -Interchangeable face plates. -White rubber mallet. -Durable plastic case. -Oil, goggles and wrenches included. -3-in-1 design fastening system. -7 Year limited warranty. -Dimensions: 22.75" H x 16.75" W x 3.5" D. Specifications: -Fastener gauge: 15.5 (staples) 16 (cleats). -Fastener range: 1.5" - 2" and 0.25" crown staples from 1.5 - 2". -Operating pressure: 70 - 115 psi. -Magazine capacity: 100 - 120 pcs.
From 1924 to 2016 DeWalt continues to design and optimize professional workhorse solutions- tools, accessories and service - to ensure absolute confidence for the toughest jobsite conditions. We are DeWalt (Dewe2), and we are guaranteed tough. Includes mallet, oil, wrenches, 1/4" (6.4 mm) air fitting with dust cover
This high-speed, air-powered flooring cleat nailer offers better productivity than non-pneumatic nailers. The tool drives L-shaped 1-1/2- to 2-inch flooring cleats precisely, at a proper angle and depth, every time in 3/4-inch hardwood flooring. Made of aircraft-grade aluminum for job site durability and low weight, the unit also has an extra-wide composite base plate for added stability. The nailer's long-reach handle gives users added comfort and control. This nailer provides 420 in./lbs. of driving power, and has an operating pressure of 60 and 100 psi. It shoots 1-1/2- to 2-inch fasteners, and has a generous 110-fastener magazine capacity to reduce the time you spend reloading. Your purchase also includes a mallet.
15-1/2ga. 2-in-1 Floor Nailer Be a pro when it comes to installing your hardwood floors with the 2-in1 Floor Nailer/Stapler . It can shoot both staples and nails without any extra conversion kit. The lightweight nailer has an extra-long handle to reduce back strain and to promote a quicker installation pace. This flooring nailer ships with a manual which details upkeep and daily use for the item. It is designed for use with 16 gauge 1-1/2 and 2 floor cleats and 15.5ga. 3/4 to 2 floor staples. Fe
Ramsond has quickly become a recognized name for the quality and durability of its products. The Ramsond RMM4 2-IN-1 flooring stapler & cleat nailer combination is another testament to the recognition that Ramsond tools now enjoy. With over 30,000 units sold in North America, the RAMSOND (R) RMM4, patented combination 2-in-1 hardwood cleat nailer and stapler is an engineering marvel. It shoots both cleat nails and staples. It shoots 15.5 and 16 gauge staples ranging from 1 to 2 inches, and "L" cleat ranging from 1-1/2" to 2". The 2-in-1 magazine has a capacity of 100 staples/cleats. It is highly durable and contractor/industrial quality, yet light weight and agile. The body of this gun is constructed of durable die-cast alloy for job site durability and low weight. It comes with an extra-wide composite non-marring base plate for added stability and protection against scratches to the flooring surface. It provides a conveniently long reach handle with an ultra-padded cushioned grip for balance and optimal operating comfort, stability and safety. Internally, the driver blade is constructed of a very tough heat treated and hardened steel. The composite base plate designed to allow the user to drive fasteners much faster and closer to the wall while protecting the flooring surface from marring. This ergonomically designed multifunctional tool is manufactured under the strict ISO guidelines for quality control. With nearly 30,000 sold, this product has become a symbol for reliability and durability.
This is a factory reconditioned product. Reconditioned generally means that the product has been returned to the manufacturer, who brings the product back to like new condition. Some products may contain cosmetic blemishes. Includes Flooring Stapler - U/MIIIFS, Graphite Mallet
Hardwood Flooring Nailer for installing hardwood floors between 1/2 - 3/4 inches thick. Used by many contractors and DIY floor installers this tool works well for all skill levels. The sturdy long handle allows for great control and keeps you from breaking your back. The nail magazine holds 100 flooring nails, and nail length can vary between 1 1/2" to 2" depending on what you need. The air inlet is standard 1/4". Air consumption is low at 4.5 CFM and allows you to use a small compressor. Input pressure should be controlled between 60 and 100 PSI. With a little practice this tool will allow you to lay hundreds of square feet per day. Depending on the type of wood you will need to vary the input pressure. Bamboo is very hard and brittle and requires a low pressure to prevent damage. Teak and some other very dense hard woods will require 100 PSI. You should test on a piece of scrap plank to make sure you are getting good results. The hardwood flooring nailer is used by placing it on the edge of a piece of hardwood flooring. The included mallet is then used to strike the actuator and fire the cleat nail in. The most difficult part of the process is just moving the flooring nailer around. Include in the kit is a Carrying Case, Hardwood Flooring Nailer , Safety Glasses, Air Tool Oil, Base Plate, S3 Hex Key S4 Hex Key S5 Hex Key Wrench, and Instruction Manual.
Can be used on 1/2", 5/8" and 25/32" floor thickness, ,Magazine Capacity (Staples): 100 PCS, ,Magazine Capacity (Cleat Nails): 120 PCS, ,Operation Pressure: 60-115 PSI, ,Purchase Includes: Flooring Cleat Nailer/Stapler Gun. High Quality Mallet. Regulation Eye Goggles. Air Tool oil. Extra Non-Marring Base Plate Cover. Hex Wrenches.
This hardwood flooring nailer drives "L" & "T" shape cleat nails from 1-1/2-Inch to 2-Inch length and staples from 1-1/2-Inch to 2-Inch. The die cast lightweight aluminum body with long handle for easy operation and the ergonomic design makes for less fatigue. Weighs 12-Pound The well balanced hardened driver blade adds a longer life to the nailer. Adjustable depth control. It's composite base eliminates scratch and damage to wood surfaces. Includes: 2 allen wrenches, rubber mallet, spacer and bumper. Load capacity: 120 nails, 92 staples. Operating air pressure: 70-110 PSI. Dimensions: 21-Inch x 19 - 1/4-Inch x 1/4-Inch
Flooring Stapler for installing hardwood floors between 1/2 - 3/4 inches thick. Used by many contractors and DIY flooring installers this tool works well for all skill levels. The sturdy long handle allows for great control and keeps you from breaking your back. The staple magazine holds 100 flooring staples, and staple length can vary between 1 1/2" to 2" depending on what you need. The air inlet is standard 1/4". Air consumption is low at 4.5 CFM and allows you to use a small compressor. Input pressure should be controlled between 60 and 100 PSI. With a little practice this tool will allow you to lay hundreds of square feet per day. Depending on the type of wood you will need to vary the input pressure. Bamboo is very hard and brittle and requires a low pressure to prevent damage. Teak and some other very dense hard woods will require 100 PSI. You should test on a piece of scrap plank to make sure you are getting good results. The flooring stapler is used by placing it on the edge of a piece of hardwood flooring. The included mallet is then used to strike the actuator and fire the staple in. The most difficult part of the process is just moving the flooring stapler around. Included in the kit is a Carrying Case, flooring Stapler , Safety Glasses, Air Tool Oil, Base Plate, S3 Hex Key S4 Hex Key S5 Hex Key Wrench, and Instruction Manual.
Good News: NOW this Nailer come with the \"Modeled Grey Carrying Case\"! The Lotos 2-in-1 Flooring Nailer and Cleat Stapler is an essential flooring tool that is made to be both easy-to-use and durable. Professional flooring installers prefer to use this Nailer and Stapler to meet their flooring needs. The result of engineering excellence, the 2-in-1 hardwood cleat nailer and stapler shoots both cleat nails and staples without needing to change magazines. This tool shoots both 15.5- and 16-gauge staples ranging from 1 to 2 inches and "L" cleats ranging from 1-1/2" to 2"; both are held in a magazine capable of holding up to 100 staples or cleats. The standard-sized staples and cleats are easily obtainable from any hardwood store. The body of the gun, constructed from die-cast alloy, is both durable and lightweight, meeting the needs of contractors and industrial companies. Adding stability, an extra-wide composite non-marring base plate is used to protect the flooring from scratching as well as allowing the user to drive fasteners faster and closer to the wall. This Nailer and Stapler is of the highest quality and guarantees a better flooring experience.
Portamatic evolution, 18 gauge floor nailer, includes hammer, specifically designed for the installation of 3/8 inch to 3/4", 10-19mm, engineered & solid wood flooring including bamboo flooring, use with 18 gauge 1-3/4", 1-1/2 inch or 1-1/4 inch L type barbed flooring nails, compact design allows you to get closer to the end walls, wide profile shoe for increased stability, quick load magazine, ergonomic comfort grip handle, fully adjustable shoe for accurate configuration to varying flooring thickness, holds 110 nails, use with nails #41801, TV #128-358 & #41803.This product adds a great value. Product is highly durable and very easy to use. This product is manufactured in china.
The Amvent PRO-X 2-in-1 Hardwood Flooring Cleat Nailer and Stapler is one of America's best-selling hand tools, with thousands of units sold. Engineered for versatility, strength, and durability, the air-powered PRO-X is capable of firing both cleat nails and staples (15.5 and 16-gauge staples from 1 to 2 inches, "L" cleat from 1-1/2 in. to 2 in. ), it holds a maximum capacity of 100 staples or cleats. It remains light and agile while still being highly durable and maintaining contractor/industrial quality. The body of the PRO-X is constructed of durable die-cast alloy for job site strength with low weight. It comes with several extra-wide composite non-marring base plates for added stability and protection against scratches to the flooring surface. The plates are designed to allow the user to drive fasteners much faster and closer to the wall, while giving added protection to the flooring material itself. The PRO-X also has a conveniently long reach handle with an ultra-padded cushioned grip providing balance, optimal comfort, stability, and safety. The internal driver blade is constructed of very tough heat treated, hardened steel. This ergonomically designed multifunctional tool is manufactured under the strict ISO guidelines for quality control. The Amvent PRO-X - The entire tool you need for any flooring job.
GR200FS Features: -Fastener Range:1-1/2 to 2". Dimensions: -Overall Product Weight:9 -Overall Depth - Front to Back:18 -Overall Width - Side to Side:3.1 -Overall Height - Top to Bottom:18.8
The Porter-Cable FCN200 Two-Inch Flooring Cleat Nailer drives 1-1/2 to 2-inch cleat nails quickly and efficiently. Durable and built to last, this nailer features a 100-cleat, rear-load, gravity-feed magazine with bypass pusher, and it has a well-balanced, stable design for dependable results in both traditional and engineered hardwoods.
The Porter-Cable FCN200 Two-Inch Flooring Cleat Nailer
At a Glance:Drives L-shaped cleats from 1.5 inches to 2 inchesPneumatic driving action of 70-100 PSIStrong, lightweight aluminum housingErgonomic designNo assembly required
Durable, lightweight aluminum construction is heavy-duty without sacrificing comfort.Balanced, Ergonomic, and Powerful
The FCN200 features a balanced, ergonomic design, and it stands upright for easy, stable use. It also has a low center of gravity that allows it to stand independently without falling over.
And because the FCN200 is made from durable, lightweight die-cast aluminum, it's heavy-duty enough to complete tough jobs, yet comfortable enough for extended use.
The FCN200 uses a compressor to provide air at approximately 70-100 PSI. It weighs just 13 pounds and arrives preassembled with an angled air hose nipple.
L-Shaped Cleat Extends Floor-Life
Whereas traditional flooring nailers use staple fasteners that don't allow for wood expansion and can shorten the life of a floor, the FCN200 utilizes an L-shaped cleat as its fastener. This cleat allows the floor to contract and expand naturally, even as it holds the floor in place.
And because standard 3/4-inch-thick solid hardwood flooring requires 2.0-inch cleats for secure installation, the FCN200 accepts cleats measuring from 1.5 to 2.0 inches. This means you can handle flooring materials of various thicknesses, including thinner engineered woods.
Additionally, the hammer head is short enough to allow the compressor to get close to the wall for installation of starting rows.
What's in the Box
FCN200; mallet; oil; wrenches; and 1/4-inch air fitting with dust cover.
The Freeman 3-in-1 Flooring Nailer/Stapler has the ability to equip 3 types of flooring fasteners (T-Cleats, L-Cleats and Staples) for the professional and do-it-yourselfer alike. The PDX50C is only 9.5 pounds, which will relieve some strain when working on long flooring projects. It is also equipped with an anodized aluminum magazine, no mar protection plate, air filter/anti-dust cap, one piece heat treated driver blade, self leveling front foot and high quality internal wearable parts. The PDX50C can be used on solid wood tongue and groove flooring measuring from 1/2-Inch to 23/32-Inch in thickness. The PDX50C is the first of its kind on the market due to several factors: overall weight, eliminates the need for a prefinished flooring adapter and comes standard with a 3 pound fiberglass handle mallet. Like all Freeman nailers, the PDX50C nailer/stapler is also backed by the Freeman 7 Year Limited Warranty.